[fedora-arm] Fedora 27 not boot on BBB

2018-03-13 8:18 GMT+09:00 Peter Robinson <pbrobinson@gmail.com>:
> On Mon, Mar 12, 2018 at 10:47 PM, sakurai <sakurai@pugpug.org> wrote:
>> Hi Peter,
>>
>> Thank you for your prompt comment.
>> I removed uEnv.txt but following message was displayed.
(snip)
>
> I don't know what you've done to now, you're likely possibly better
> off starting again with arm-image-installer to setup the image again
> with am335x_evm and then try booting with the boot button held down.

I tried again using arm-image-installer by following command.

> fedora-arm-image-installer --image=Fedora-Server-armhfp-27-1.6-sda.raw.xz --target=am335x_evm --media=/dev/sdd --norootpass --resizefs --addconsole --selinux=off

Not am335x_boneblack? Anyway I installed using arm335x_evm this time.

My boot loader may be new because Angstrom will not boot without
holding the boot button.

> You might also want to give the full output.

Here is the full output.

U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
mmc_send_cmd : timeout: No status update
reading u-boot.img
reading u-boot.img


U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14)

I2C: ready
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: No NAND device found!!!
0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
micro SD card found
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
** Unable to read file uEnv.txt **
gpio: pin 55 (gpio 55) value is 1
** File not found /boot/uImage **
U-Boot#

--
SAKURAI, Atsushi <sakurai@pugpug.org>
_______________________________________________
arm mailing list -- arm@lists.fedoraproject.org
To unsubscribe send an email to arm-leave@lists.fedoraproject.org