Hi Fred,
Am 03.04.20 um 13:10 schrieb Fred van Zwieten:
> I haven't retried it yet, but I do have some extra info on my previous
> (and failed) attempt:
>
> I used arm-image-installer as the tool. As it does not yet have a rpi4
> target, I used the rpi3 value. It does boot, but, like I said, it
> hangs in a later stage. I will provide screenshots when I am able to
> test again.
>
> This is the (relevant) output from /proc/cpuinfo:
> Hardware : BCM2835
> Revision : c03111
> Serial : 1000000094b1358a
> Model : Raspberry Pi 4 Model B Rev 1.1
this should work with Linux 5.6. So i don't have an idea what's the
problem here.
Rev 1.2 needs recent changes to sdhci-iproc and the devicetree.
Best regards
Stefan
>
> - Fred
>
> On Fri, Apr 3, 2020 at 12:25 PM Andreas Reschke <arm_ml@rirasoft.de
> <mailto:arm_ml@rirasoft.de>> wrote:
>
> Hello Dirk,
>
> I've tried it with balenaEtcher: It works !!
>
> Thank you for that tip !!
>
> Andreas
>
> PS: I dind't know why it not works with xzcat and dd but now I have a
> working method.
>
> Am 03.04.20 um 10:23 schrieb Dirk Streubel:
> >> Hello together,
> >>
> >> Hello Dirk
> >>
> >> how did you you install
> Fedora-Minimal-32_Beta-1.2.aarch64.raw.xz on SD-Card?
> >>
> >> Just xzcat Fedora-Minimal-32_Beta-1.2.aarch64.raw.xz | dd
> of=/dev/sdc status=progress bs=4M
> >>
> >> didn't work for me. All I get is a dracut shell
> >>
> >>
> >> Thanks
> >>
> >> Andreas
> > Hello Andreas,
> >
> > yes, i installed the two Version yesterday on a 64 GB SD Card.
> >
> > Image has been unpacked with all necessary tools.
> >
> > For installation on the SD Card i use balenaEtcher. That Program
> works fine here.
> >
> > Dirk
> >
> >
> >
> >
> >
> >> _______________________________________________
> >> arm mailing list -- arm@lists.fedoraproject.org
> <mailto:arm@lists.fedoraproject.org>
> >> To unsubscribe send an email to
> arm-leave@lists.fedoraproject.org
> <mailto:arm-leave@lists.fedoraproject.org>
> >> Fedora Code of Conduct:
> https://docs.fedoraproject.org/en-US/project/code-of-conduct/
> >> List Guidelines:
> https://fedoraproject.org/wiki/Mailing_list_guidelines
> >> List Archives:
> https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
> > _______________________________________________
> > arm mailing list -- arm@lists.fedoraproject.org
> <mailto:arm@lists.fedoraproject.org>
> > To unsubscribe send an email to
> arm-leave@lists.fedoraproject.org
> <mailto:arm-leave@lists.fedoraproject.org>
> > Fedora Code of Conduct:
> https://docs.fedoraproject.org/en-US/project/code-of-conduct/
> > List Guidelines:
> https://fedoraproject.org/wiki/Mailing_list_guidelines
> > List Archives:
> https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
> _______________________________________________
> arm mailing list -- arm@lists.fedoraproject.org
> <mailto:arm@lists.fedoraproject.org>
> To unsubscribe send an email to arm-leave@lists.fedoraproject.org
> <mailto:arm-leave@lists.fedoraproject.org>
> Fedora Code of Conduct:
> https://docs.fedoraproject.org/en-US/project/code-of-conduct/
> List Guidelines:
> https://fedoraproject.org/wiki/Mailing_list_guidelines
> List Archives:
> https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
>
>
> _______________________________________________
> arm mailing list -- arm@lists.fedoraproject.org
> To unsubscribe send an email to arm-leave@lists.fedoraproject.org
> Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/
> List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines
> List Archives: https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
_______________________________________________
arm mailing list -- arm@lists.fedoraproject.org
To unsubscribe send an email to arm-leave@lists.fedoraproject.org
Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/
List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines
List Archives: https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org
No comments:
Post a Comment