[fedora-arm] Re: Hikey board (620) with Fedora 28 minimal cannot boot

Hi,

On 05/14/2018 10:26 AM, Zamir SUN wrote:
> Hi,
>
> Today I am trying my HikeyBoard (620) with
> Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot.

So, two quick questions. What firmware & version are you using, and have
you tried booting one of the installer images?

(I tend to use the server iso image, and have had a decent bit of luck
with it).


>
> I confirmed the xz image has the same hash as is shown on the mirror. I.
> used the following command to write to my TF card.
> xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress
> bs=4M of=/dev/mmcblk0
>
> The system failed in dracut init queue timeout, with a warning "Warning:
> /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist "
>
> However I confirmed the uuid is right for my partition.
>
> Besides, I cannot type anything via minicon to it so I cannot really
> debug more right now. I am posting the last block of message via UART.
>
> So anyone have some hints for this? Thanks in advance!
>
> (P.S. Fedora 27 works fine on my hikey board).
>
>
> [ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout
> - starts
> [ 222.639909] dracut-initqueue[468]: Warning: Could not boot.
>
> Starting Setup Virtual Console...
>
> [ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1
> uid=0 au'
> ] Started Setup [ 222.738436] audit: type=1131
> audit(1520288415.819:15): pid=1'
> Virtual Console.
>
> Starting Dracut Emergency Shell...
>
> [ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0
> auid=4294'
> Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not
> exist
>
>
> Generating "/run/initramfs/rdsosreport.txt"
>
> [ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
> 400000H)
> [ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
> 1000000)
> [ 222.967237] print_req_error: 6 callbacks suppressed
>
> [ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1
>
> [ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0
>
> [ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1
>
> [ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async
> page read
> [ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
> 400000H)
> [ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
> 1000000)
> [ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1
>
> [ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0
>
> [ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1
>
> [ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async
> page read
> [ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0
>
> [ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1
>
> [ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
> 400000H)
> [ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
> 1000000)
> [ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1
>
> [ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2
>
> [ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
> 400000H)
> [ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
> 1000000)
> [ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
> 400000H)
> [ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
> 1000000)
> [ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
> 400000H)
> [ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
> 1000000)
> [ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
> 400000H)
> [ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
> 1000000)
> [ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
> 400000H)
> [ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
> 1000000)
>
_______________________________________________
arm mailing list -- arm@lists.fedoraproject.org
To unsubscribe send an email to arm-leave@lists.fedoraproject.org